log splitter valve sticking

You need to check the amount of oil first. On one side of the valve there is a inch long bolt only way I know how to describe it with a ball in the end.

Pin On Tools

If fluid is leaking from your pump disassemble it and replace all seals.

. I am borrowing my neighbors 27-ton Troy-Bilt log splitter. When the pump fails it will often send metal debris. If the log splitter seems weak or not performing as it should then there is a strong likelihood that something is not right with how the splitter system is operating.

Now start up the engine and give it a try. Works fine except and he warned me that the handle sometimes pops back to neutral when in reverse mode. Kshansen May 21 2020 19.

If your log-splitter is moving slow but still capable of splitting the wood it always has it is most likely stuck in its second stage. If youre used to the lever going one way on one log splitter you might have overlooked the valve position on a different log splitter that works differently. It happens due to either the lower level of fluid or the air present in the system.

Having a two stage pump and the automatic detent valve that my store built splitter has puts the single stage pump and non-detent valves to shame for ease of use. Articles Tractor Registry Tip of the Day. Check the manual to be sure you have proper lever position.

In the second stage or low flowhigh-pressure stage the pump produces 25 or less of its rated GPM but it does it at a higher pressure. Place the log splitter back upright and try the splitter again if it produces the same noise then loosen the bolts a little from the end of the pump 13mm and try again. I have a Power Pro log splitter made by Brave Model HP-1226F.

Other than that it works fine. The hydraulic valve has seals around the actuator rod that can wear out and fail over time. I took the valve apart cleaned it thoroughly there was some old grease whatever else and when you put it in return the detent would not release like it should would stick and almost stall the motor.

The detent cover on the hydraulic valve controls the auto-return. When attempting to split logs check that the end of the valve stem remains in contact with the face of the lever when the lever is depressed and released. Anyone ever rebuild a log splitter hydaulic valve.

Start your adjustment in small increments while re-testing the resistance until it takes just a small snap to pop it into center. Return Detent on Log Splitter Valve in reply to wsmm 09-25-2013 111353 Hello WSMM. Discussion Starter 1 Sep 1 2021.

Stuck Troubled Vintage Ads Community Album Photo Ad Archives. If still your log splitter shuts off under load most likely your hydraulic pump is jammed or stuck in its high flowlow-pressure stage described as the first stage. If youre used to the lever going one way on one log splitter you might have overlooked the valve position on a different log splitter that works differently.

Sometimes a second attempt lets it auto-reverse the ram other times I have to hold it in place to prevent it from prematurely kicking back into neutral. If the oil is found to be enough then the problem is due to the air mixed with liquid when opening the bleed valve and cycling pressure plate. Its a Huskee 22 ton and the valve is sticking both ways.

The seals on these pumps wear over time and eventually can cause hydraulic fluid to leak out of the system. 14 BMW 328D Xdrive. This will remove all the excess air trapped inside the splitter.

And now it started to stick going out and it will go out to the end and stall the engine. You can check for this issue easily. Fixing the auto-return on a hydraulic control valve usually is just a matter of tightening The bolt inside the detent cover assembly.

Remove the air from the system to solve this problem and keep the bleed. Up to 32 cash back The log splitters hydraulic control valve directs the hydraulic fluid flow to the hydraulic cylinder to extend and retract the piston and wedge. Now release the ram and put back the oil-filling plug.

To begin with check your log splitter and the wood you are trying to split. If the valve core does not pop back out when the lever is released then it requires cleaning. It should move about a 12 inch without much resistance.

If hydraulic fluid leaks from the valve body around the actuator rod replace the hydraulic valve in the log. This tutorial apply to the Energy control valve. Its working but not correctly.

Ad Browse discover thousands of brands. If it moves freely then it could be N75 valve. Reach down to the turbo with engine off and manually push the rod threw its range of travel.

Just rotate clockwise the oil-filling plug and remove the plug. Valve core requires cleaning. Another reason for a slowed-down log splitter is a jammed motor due to blockage in the fan.

Jun 9 2016. When it retracts it pulls in tight and stalls the engine. Note the force used.

When repairing a damaged pump it is important to carefully analyze and address the rest of the hydraulic system. Pushed one way it shunts oil from the pump to the base port of the cylinder causing it to extend. The spool shifted by the handle has 3 positions.

I have a Brave Log splitter and the last few weeks the detentspoil valve has become sticky after the I split a couple of hours. If not then look for blockages in the fan and remove them. The hydraulic directional valve controls the motion of the cylinder.

And it simultaneously allows oil from the rod-end port of the cylinder to flow into. My new to me Countyline Speeco 25 ton splitter control valve detent mechanism was sticking operating erratically and adjusting didnt solve the problem. Ensure that the ram is fully returned this is essential before starting the process.

If a log is not splitting all the way through then the log may be too green or too large meaning that it would require a greater force than your log. Remove the fan cover and try to turn it to see if it moves without difficulty. The VNT actuator rod may be sticking.

No power to the motor Fuse blown or RCD Tripped. First turn the log splitter over and close off the air vent remove the motor and pump 3 x 13mm headed bolts and 1 x support bolt. Lock the handle into the return position and manually pull it back into center position.

This valve is the most prevalent valve used in the residential log splitter industry. Dec 12 2005. Common problems with AL-KO and similar Chinese generic log splitters the hydraulic valve spindle breaks on the end stopping the unit from working correctly.

Joined May 14 2017. Check the position of the lever. I pulled the cap and found it contaminated with moisture and it was lubricated with a silver pastegrease.

The Hydraulic Log Splitter Valve. Also it is hard to trip the lever to get it to stop retracting. In this stage.

Read customer reviews find best sellers. A detent valve lever can be pushed up or down to put the valve into operation.

How To Fix The Automatic Return On A Log Splitter Offgridmaker Com